Tc-electronic TonePrint Editor User Manual download pdf (Page 13)

■

Modulation parameters

TC Electronic TonePrint Editor

■

Manual for software version 1.0 11

Through-Zero-Flanger parameter

Parameter range: 0 to 1023

When you set the Modulation Type parameter to

TZFlanger, delay line 1 becomes the “dry” part of

the signal. In that case, use the Through-Zero-

Flanger parameter to set the level ratio between

delay line 1 and delay line 2.

Speed parameter

Parameter range: 61.5 mHz (Millihertz) to 20 Hz

Use the Speed parameter to set the speed of

the chosen modulation effect. As setting of 1 Hz

means that one modulation cycle takes one se-

cond.

Depth 1 parameter

Parameter range: 0 to 100 %

Use the Depth 1 parameter to specify the inten-

sity of the effect. The value represents the ampli-

tude of the waveform modulating the signal.

When you have set Modulation Type to TZFlang-

er, you should set the Depth 1 parameter to a

value lower than Depth 2.

Depth 2 parameter

Parameter range: 0 to 100 %

The Depth 2 parameter is only applicable when

you have set Modulation Type to TriChorus or

TZFlanger.

In TriChorus mode, the Depth 2 parameter speci-

fies the intensity of the second chorus module. In

TZFlanger mode, the Depth 2 parameter speci-

fies the intensity of the second flange module.

The value represents the amplitude of the second

waveform modulating the signal.

Depth 3 parameter

Parameter range: 0 to 100 %

The Depth 3 parameter is only applicable when

you have set Modulation Type to TriChorus.

In TriChorus mode, the Depth 3 parameter speci-

fies the intensity of the third chorus module.

The value represents the amplitude of the third

waveform modulating the signal.

HiCut parameter

Parameter range: 20 Hz to 20 kHz

Use the HiCut parameter to reduce the high-end

frequencies in the modulation effect. Try using

this parameter if you feel the effect is too domi-

nant in your sound and turning down the Mix or

Output Level parameters doesn’t attenuate the

effect as intended.

Mix parameter

Parameter range: 0 to 100 %

Use the Mix parameter to set the relationship be-

tween the level of the dry signal and the level of

the modulation effect. If you have set Kill dry in

the Router section to On, this parameter has no

effect.

Output Level parameter

Parameter range: -100 to 0 dB

Use the Output Level parameter to set the overall

output level for the modulation effect.

Delay Time 1 parameter

Parameter range: 0.1 to 50 ms

As described earlier, a chorus or flanger is basi-

cally a delay being modulated by an LFO. Use

the Delay Time 1 parameter to change the length

of that delay. A typical chorus uses delay times

around 10 ms, while a flanger uses delays around

5 ms.

Although this is not how a chorus is normally

used, you may enjoy the “slap-back” sound re-

sulting from longer Delay Time values in the 30

to 50 ms range.

Delay Time 2 parameter

Parameter range: 0.1 to 50 ms

The Delay Time 2 parameter is only applicable

when you have set Modulation Type to TriChorus

or TZFlanger.

In TriChorus mode, the Delay Time 2 parameter

specifies the length of the delay for the second

chorus module.

In TZFlanger mode, the Delay Time 2 parameter

specifies the length of the delay for the second

flange module.

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 19

Comments to this Manuals

No comments

Tc-electronic TonePrint Editor User Manual Page 13

Comments to this Manuals

Related products and manuals for Musical Instruments Tc-electronic TonePrint Editor